Quadro Quadro2x2 Installationsanleitung PDF herunterladen (Seite 51)

QuadroM 32x/8L/26x/12Li/26xi Manual I: Installation Guide Step 2: Configuring the Quadro

In the ISDN L3 Timers area, the T302 Timer text field requires the value for the T302 timer

in milliseconds (digit values from 0 to 15000) and indicates the time frame system is waiting

for a digit to be dialed and when timer expires, it initiates the call. The timer is not applica-

ble for DMS-100 switch types. The T309 Timer text field requires the value for the T309 ti-

mer in milliseconds (digit values from 0 to 90000) responsible for call steadiness during link

disconnection within the period equal to this timer value. If the value in this field is 0, the

T309 timer will be disabled. The T310 Timer text field requires the value for the T310 timer

in milliseconds (digit values from 1000 to 120000) responsible for the outgoing call steadi-

ness when CALL PROCEEDING is already received from the destination but call confirma-

tion (ALERT, CONNECT, DISC or PROGRESS) is not yet arrived. The No Answer Dis-

connect Timer text field is only available in Network mode and requires the value for the

No Answer Disconnect Timer (digit values from 0 to 200000). This timer is used in certain

types of PBXs. The value 0 indicates that the timer is disabled. When time expires, Quadro

will play a busy tone towards the PBX if the call has been disconnected by the peer.

The D Channel Timeslot For Transmit/Receive drop down list in offers all available time-

slots to be selected for signaling data transmit/receive.

The link B Channels leads to the Signaling Type CCS - B Channel Settings page (see

below) where available timeslots may be enabled or disabled for the voice transfer. The

Force Update option can be optionally used to apply new settings immediately. This will

force the timeslot(s) to be restarted and any active connection on the selected timeslot(s)

will be interrupted. The Restart option can be used to bring timeslot(s) to the initial idle

state on the both sides. Note, that when applying one of these options, any active traffic on

the timeslot(s) will be terminated. Edit will display another page, where the signaling set-

tings for the selected timeslots may be specified in detail.

Bearer Establishment Procedure allows you to select the session initiation method on the

B channels. One of the following possibilities of the transmission path completion prior to

receipt of a call acceptance indication can be selected:

• on channel negotiation at the destination interface;

• on progress indication with in-band information;

• on call acceptance.

Called Party Type of Number and Calling Party Type of Number fields indicate corre-

spondingly the type of the called party’s and of the calling party’s number.

Called Party Numbering Plan and Calling Party Numbering Plan drop down lists indi-

cates correspondingly the numbering plan of the called party's and calling party's number.

The Route Incoming Call to drop down list contains Attendant, routing agent with two

kinds of call routing possibilities, and all extensions of Quadro and allows selecting the des-

tination where incoming calls will be routed to. Choosing Routing will request the caller to

pass the authentication (if enabled) and will invite him to dial the destination number to

connect the user within the Quadro Network. Choosing Routing with inbound destination

number will request the authentication (if enabled) and then will automatically use the ini-

tially dialed number to connect the destination without any additional dialing.

Attention: When Quadro acts in the Network mode with the Attendant as a destination to

route the incoming calls to, digit forwarding should be disabled on the private PBX side

otherwise incoming digits may be mistaken as a special calling codes on the Quadro’s At-

tendant.

The value for Switch Type depends on the CO when acting in the User mode and the pri-

vate PBX capabilities when acting in the Network mode.

Attention: A timeslot can be used either for voice or signaling data transfer. The configura-

tion prevents the selection of a timeslot from the B channel list if it has already been se-

lected from the D Channel receive/transmit drop down list.

QuadroM 32x/8L/26x/12Li/26xi; (SW Version 5.2.x) 51

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 75 76

Kommentare zu diesen Handbüchern

Keine Kommentare

Quadro Quadro2x2 Installationsanleitung Seite 51

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für PBX-Systeme (Premise Branch Exchange) Quadro Quadro2x2