Quadro Quadro16xi Installationsanleitung Seite 100
- Seite / 150
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Quadro Manual II: Administrator's Guide Administrator’s Menus
Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 99
The Use RTP Proxy checkbox is available for SIP and IP-PSTN call types and is applicable when a route is used for calls through Quadro between
peers that are both located outside the Quadro. When this checkbox is selected, RTP streams between external users will be routed through
Quadro. When the checkbox is not selected, RTP packets will move directly between peers.
The Call Duration Limit checkbox is available for SIP, IP-PSTN and PSTN call types and is used to limit the duration of the call placed with the
selected routing rule. If this checkbox is not selected, the call duration will be unlimited. This checkbox selection enables the Maximum Duration text
thorization, and Accounting (AAA) settings:
field where the maximum duration of the call (in seconds) should be defined. Once the call duration reaches the value defined here, the call will be
disconnected without prior notice.
The AAA Required checkboxes are used to choose one or more of the following Authentication, Au
• Local Authentication – with this checkbox selected, callers will need to pass authentication through the Local AAA Table
when dialing the
current pattern.
• RADIUS Authentication and Authorization – this checkbox is present when a RADIUS client is enabled. With this checkbox selected,
callers will need to pass the authentication through RADIUS server (see above) when dialing the current pattern.
CDRs (call detail reports) of the calls made through this routing record will be sent to the RADIUS server. This checkbox
to
sent with CDR to the RADIUS server and might be used by a billing program for grouping the calls having the same Identity
C approval before placing a call with the specific routing rule. When this checkbox is
s a request to the call controlling application for the managing
e of dialog box, depending on the call controlling application). If
son(s) - indicates possible failure reasons. Failure reasons vary depending on the call type selected on the previous page. If the
specified destination.
o Wrong Number - available for PBX, SIP, SIP Tunnel, and IP-PSTN call types and indicates cases when the dialed number is wrong.
rization, negotiation, not supported or
The SIP Privacy manipulation radio buttons group is only available for the SIP call type and allows you to select the security of the SIP route by
means of hiding (or replacing, depending on the configuration of the SIP server) the key headers of the SIP messages used to establish the call.
• Default Privacy – with this selection, Quadro specific SIP privacy will not be applied and all privacy will rely on the configuration of the SIP
Server.
• Disable Privacy – with this selection, SIP call security will not be disabled and all headers of the SIP message will be transparently visible
to the destination.
• Enable Privacy - with this selection, SIP privacy will be specified for the corresponding route. This selection enables a group of
checkboxes in order to choose the key headers that are to be fully or partly hidden or replaced. The Require Privacy checkbox selection
is used to restrict the delivery of the SIP message if any of the selected headers cannot be hidden (or replaced, depending on the
configuration of the SIP server) before being sent to the destination.
• The RADIUS Accounting checkbox is accessible when the RADIUS Client is enabled. With this checkbox selected, no authentication will
take place, but
selection enables the Client Code Identification checkbox.
If the authentication is configured based on the caller’s address, callers will pass the authentication automatically; otherwise they will be required
identify themselves by a username and a password.
The Client Code Identification checkbox selection activates the code identification feature: a caller, after dialing the destination phone number, may
optionally enter “*” and then an Identity Code. An Identity Code is an arbitrary digit string entered by the user to identify a specific call or call group.
The Identity Code is
Code.
The Check with 3PCC checkbox is used to request a 3PC
selected and the corresponding routing rule is used to place a call, Quadro send
person to accept or reject the specific call (it can be a popup window or any other typ
the request is accepted, the call will be placed. Otherwise, if the request is rejected, the call will be skipped. In case of no feedback from the call
controlling application, the call will be accepted after a timeout defined in the configuration of the call controlling application.
The Failover Reason(s) radio buttons indicate whether the system should use the next matching pattern if call setup with the current routing rule
fails and allows choosing the reasons to be considered as a failover.
• None - indicates that matching patterns should not be used regardless of the failover reason.
• Failover Rea
call cannot be established due to selected Failure Reasons, the call routing table will be parsed for the next matching pattern and, if found, the
call will be routed to the
o Cannot Establish Connection - failure reason is available for FXO and ISDN only and indicates cases when connection cannot be
established.
o Busy - available for PBX, SIP, SIP Tunnel, and IP-PSTN call types and indicates cases when the dialed destination is busy.
o Network Failure - available for SIP, SIP Tunnel, and IP-PSTN call types and indicates cases when system overload, network failure or
timeout expiration occurred.
o System Failure - available for SIP, SIP Tunnel, and IP-PSTN call types and indicates cases indicated in Network Failure and Other fail
reasons.
o Other - available for SIP, SIP Tunnel, and IP-PSTN call types and indicates cases when autho
request rejected or other unknown errors occur.
• Any stands for all failure reasons mentioned in the Failover Reason(s) group.
The Transport Protocol for SIP messages manipulation radio buttons group is available for SIP or IP-PSTN call types only and allows you to select
the transport (UDP, TCP or TLS) to transmit the SIP messages through.
- Edition 1, June 2011 1
- Table of Contents 2
- Quadro’s Graphical Interface 6
- Recurrent Buttons 7
- Recurrent Functional Buttons 7
- Administrator’s Menus 8
- System Security Management 12
- • User Rights Management 13
- • IP Line Settings 13
- • Firewall/NAT 13
- Network Status 15
- Memory Status 19
- Hardware Status 20
- SIP Registration Status 20
- IP Lines Registration Status 20
- License Status 21
- IP Routing Configuration 21
- Configuration Management 23
- Time/Date Settings 28
- Mail Settings 29
- SMS Settings 30
- Firmware Update 30
- Automatic Firmware Update 32
- Networking Tools 33
- SNMP Settings 34
- Diagnostics 35
- System Logs 35
- Fig. II-64: Features page 37
- Upload Language Pack 38
- User Rights Management 39
- Users Menu 41
- Extensions Management 41
- User Extension Settings 43
- Call Park Extension Settings 49
- Attendant Extension Settings 55
- • PSTN – calls to PSTN 56
- • User Input 58
- • No input 58
- • Signs (“*” and “#”) 58
- Add Multiple Extensions 61
- Extension Codecs 62
- Call Park Service 63
- Recording Box 64
- Receptionist Management 65
- * key combination (see 67
- Authorized Phones Database 69
- Call Back Services 70
- Telephony Menu 72
- Call Statistics 72
- RTP Statistics 75
- FAX Statistics 76
- SIP Settings 76
- Host aliases for SIP 77
- RTP Settings 77
- NAT Traversal Settings 78
- Line Settings 81
- Onboard Line Settings 81
- IP Line Settings 82
- Supporte 84
- IP Phones Templates 85
- Phones Logo 86
- FXS Gateway Management 87
- Loopback Settings 88
- Hot Desking 88
- FXO Settings 89
- Gain Control 95
- SIP Tunnel Settings 95
- • Failover Rea 100
- Local AAA Table 103
- Global Speed Dial Directory 104
- Allowed C 104
- Best Matching Algorithm 106
- VoIP Carrier Wizard 108
- RADIUS Client Settings 109
- Voice Mail Common Settings 111
- Dial Plan Settings 112
- 3PCC Settings 112
- RTP Streaming Channels 113
- Call Recording Settings 113
- Advanced PPP Settings 117
- VPN Configuration 117
- Dynamic DNS Settings 124
- Firewall and NAT 125
- Advanced Firewall Settings 125
- IP Pool 128
- IDS Log 130
- Network Menu 131
- DNS Settings 131
- DNS Server Settings 131
- Registration Form 134
- Voice Mail Profiles 135
- Administrator’s Logout 139
- Welcome 140
- Administrator Settings 141
- Extension Settings 147
- EPYGI TECHNOLOGIES, LTD 149
- Software License Agreement 149
Verwandte Produkte und Handbücher für PBX-Systeme (Premise Branch Exchange) Quadro Quadro16xi
(2 Seiten)
(11 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern