Quadro Quadro16xi Installationsanleitung PDF herunterladen (Seite 91)

Quadro Manual II: Administrator's Guide Administrator’s Menus

Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 90

• In case of connection to the CO (User interface type is selected on the Quadro) choose this option if there can be other devices connected to

Network interface type is selected on the Quadro) choose this option if there can be other devices connected to

atic mode.

tor before configuring the ISDN connection type.

type selected on the previous page of ISDN Wizard:

this

the same ISDN trunk from CO except the Quadro.

• In case of connection to PBX (

the same ISDN trunk from Quadro except for the PBX.

• In both cases, with this selection Quadro sets the TEI to autom

Please Note: Consult with your CO operator or network administra

The ISDN Wizard - Page 2 content is dependent on the connection

The next page is ISDN Wizard – MSN Settings page which is

used to turn on the MSN configuration. It is recommended to

enable the MSN when there are multiple ISDN devices

connected to the same ISDN bus. If the MSN is enabled on

page, the next page will require the MSN table configuration.

Fig. II-157: ISDN Wizard – ISDN PRMP Settings

this page will ring upon

corresponding MSN number comes in.

n require the MSN

lease Note: At least one MSN number should be defined in

em displays an error message if the same

with

ovided by the CO. If this

For MSN service enabled, the Routing Settings page is used to assign MSN numbers to the certain destinations on the Quadro. The MSN number

can be assigned to the Quadro’s extensions, to the Auto Attendant, or to the routing agent. The destination selected from

incoming call to the

The fields in the MSN Number colum

mbers allocated to the Quadro.

this page. The syst

MSN number is used twice in this page.

The Route Incoming Call to drop-down lists are used to select

the destination where the incoming call addressed to the certain

MSN number will be routed. Choosing the Routing

inbound destination number selection will automatically use

the initially dialed number to connect the destination without any

additional dialing. If MSN is disabled on the ISDN Wizard - MSN

Settings page, the ISDN Wizard - Routing Settings page

contains only one Route Incoming Call to drop-down list.

Selecting the Use Default outgoing Caller ID allows you to

overwrite the source caller information with the one specified in

the Default outgoing Caller ID field when placing outgoing

calls toward the CO. The Default outgoing Caller ID field

requires the caller ID for the outgoing calls from the Quadro

through the ISDN trunk. That number should be registered at

e O and can be one of the MSNs prth C

checkbox is enabled but no value is defined in the Default

outgoing Caller ID, empty caller information will be sent to the

CO. If this checkbox is disabled, the source caller information

will be forwarded to the CO.

Fig. II-158: ISDN Wizard – Routing Settings

ckbox if you wish to adjust trunk’s L2 and L3 Settings manually, otherwise leave this checkbox unselected to use

The iguration only and contains L2&L3 Settings. This

Adva n the previous page of the wizard. This page contains the following components:

500 to 9999) between the transmitted signaling packet

and its acknowledgement received.

Select the Advanced Settings che

the system default values.

ISDN Wizard – L2&L3 Settings is used for advanced conf

nced Settings checkbox is selected o

page only appears when the

ISDN L2 Timers:

• Excessive Ack. Delay T200 configures the period in milliseconds (numeric values from

1 2 ... 86 87 88 89 90 91 92 93 94 95 96 ... 149 150

Kommentare zu diesen Handbüchern

Keine Kommentare

Quadro Quadro16xi Installationsanleitung Seite 91

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für PBX-Systeme (Premise Branch Exchange) Quadro Quadro16xi